Ubiquiti UA-SK-Elevator
Ubiquiti UA-SK-Elevator
Ubiquiti UA-SK-Elevator 
General
Manufacturer UBIQUITI
Model Ubiquiti UA-SK-Elevator
Manufacturer Part No UA-SK-Elevator
Compatible Country Middle East, Africa, Iran, Dubai
Country of Origin California

Ubiquiti UA-SK-Elevator Elevator Starter Kit

  • UBIQUITI
  • Brand Store:  UBIQUITI   decoration   decoration
  • Model: Ubiquiti UA-SK-Elevator
  • Availability: Out Of Stock
  • Part No: UA-SK-Elevator

Key features

Connects to in-elevator readers with PoE to authorize floor selection. Supports up to 18 floors with digital inputs for elevator car status and emergency. #1: (1) Elevator Hub #2: (1) G2 Reader #3: (2) 2-wire PoE extenders #4: (10) Access Cards

Ubiquiti UA-SK-Elevator

UA-Hub-Elevator Mechanical Dimensions 129.3 x 244.7 x 33.6 mm (5.1 x 9.6 x 1.3") Enclosure material Polycarbonate Mounting material Polycarbonate Hardware Networking interface (4) 10/100/1000 Base-T Management interface (1) 10/100/1000 Base-T Power method PoE++ UL 294 Power-limited Class 2 PSU UL 60950-1/62368-1 LPS/PS2 PSU Max. power consumption 7W (Without PoE output) PoE input (1) PoE++, 50V DC, 1.2A PoE output PoE passthrough, (4) PoE, 50V DC, total 42W ESD/EMP protection Air: +8kV, contact: +4kV Digital input (5) Car position (6) Car status; Up/down/stop/full/door open/door close (1) Emergency Outputs (18) Relays Rating 30V DC/2A Buttons (1) Factory-reset Terminal blocks Ambient operating temperature -10 to 40 C (14 to 104 F) Ambient operating humidity 5 to 95% noncondensing Certifications CE, FCC, IC, UL 62368-1, CSA C22.2 No. 62368-1 LEDs PoE in Steady white: Pending adoption Steady blue: Adopted Alternating white/blue: Firmware updating Input terminals Blinking white: Active signal Output relays Blinking white: Relay triggered UACC-Extender-2Wire-Tx/Rx Mechanical Dimensions 40 x 105 x 25 mm (1.6 x 4.1 x 1") Enclosure material Polycarbonate Mounting material Polycarbonate Hardware Networking interface (1) 10/100 MbE (1) Homeplug AV Management interface (1) 10/100 MbE Power method PoE++ Max. power consumption 3W (Without PoE output) PoE input (1) PoE++, 50V DC, Max. 1.2A PoE output (1) PoE+, 48V DC, 0.72A ESD/EMP protection Air: +8kV, contact: +4kV LED White Ambient operating temperature -10 to 40 C (14 to 104 F) Ambient operating humidity 5 to 95% noncondensing Certifications CE, FCC, IC UA-G2 Mechanical Dimensions 93 x 40 x 36.5 mm (3.7 x 1.6 x 1.4") Enclosure material Polycarbonate, glass Mounting In wall, gang box Weatherproofing IP55 Hardware Networking interface (1) 10/100 MbE RJ45 port Connectivity BLE 4.1 Power method PoE UL 294 Power-limited Class 2 PSU UL 60950-1/62368-1 LPS/PS2 PSU Supported voltage range 48V DC Max. power consumption 5W ESD/EMP protection Air: +15kV, contact: +8kV Sensors Proximity sensor Speaker (1) 8 ohm, 0.7W LEDs Steady white: Pending adoption Steady blue: Adopted Alternating white/blue: Firmware updating Strobing red: Emergency lockdown Steady green: Emergency evacuation (2) Rapid flashing blue: NFC credential authenticated (2) Rapid flashing red: NFC credential authentication failed Breathing blue: Ready to register NFC cards Button (1) Factory-reset NFC frequency 13.56 MHz NFC read range < 30 mm NFC standards ISO 14443A, 14443B, 15693 NFC technology NFC Tag 1,2,3,4,5 MIFARE Classic MIFAREPlus MIFARE Ultralight MIFARE DESFire Operating environment Outdoor use Ambient operating temperature -30 to 45 C (-22 to 113 F) Ambient operating humidity 5 to 90% noncondensing Software information The software version of a product can be checked at https://unifi.ui.com UL 294 level Destructive attack: Level I Line security: Level I Endurance: Level I Standby power: Level I UL 294 statement Compliance with IEEE 802.3 specifications was not verified as part of UL 294. The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits. PoE cabling requirements Cable 5e cabling is the minimum performance category recommended. The performance category utilized should match the transmission speed required at the installation site. The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 26 AWG (0.13 mm 2 ) for patch cords; 24 AWG (0.21 mm 2 ) for horizontal or riser cable. CAN/ULC-60839-11-1 Grade Grade assignment: I Certifications CE, FCC, IC, UL 294, CAN/ULC-60839-11-1 Document number,and issue date and/or revision level UA-G2/UA-G2-Black, V02 UA-Card Mechanical Dimensions 85.6 x 54 x 0.8 mm (3.4 x 2.1 x 0.03") Format ISO 7810 ID-1 NFC frequency 13.56 MHz NFC technology ISO/IEC 14443 Type A MIFARE DESFire UniFi Access Proprietary Security Protocol



show more
General
Manufacturer UBIQUITI
Model Ubiquiti UA-SK-Elevator
Manufacturer Part No UA-SK-Elevator
Compatible Country Middle East, Africa, Iran, Dubai
Country of Origin California

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
Track Your Order Here Whatsapp +97142380921